Westmere · Leak detection
Leak Detection in Westmere
A leak under a bathroom after new taps are fitted needs prompt investigation. A damp ceiling below, water in a vanity, or moisture beneath the floor needs checking, even if the taps themselves look dry.
- PGDB licensed
- Site Safe member
- Impac Prequal assessed
- Kiwi-owned since 2012
How it works
Call or enquire
Phone us or send the address and what you’re seeing.
We assess
A licensed Stately plumber looks at the job on site.
Clear quote
You get a plain explanation and a clear quote before work starts.
Job done and tidied
We finish the work and leave the site clean.
The timing gives us a useful starting point, but we check the source before recommending a repair. Stately covers Westmere, and our investigation follows the new fittings, their connections and the route water could take into the space below.
What to notice before we arrive
Stop using the affected taps and note when the moisture first appeared. Tell us whether it shows up while a tap runs, shortly afterwards, or while the bathroom is unused. Photos of the first wet patch and any changes help us understand the sequence without repeatedly wetting the area.
Keep people clear of a sagging ceiling, and avoid touching wet electrical fittings. If water is actively escaping, turn off the water supply only if you know where the shut-off is and can reach it safely. Do not remove tap handles, tighten hidden connections or lift bathroom flooring.
Checking the new taps and nearby connections
We begin by asking which taps were replaced and what work was done around them. An accessible connection disturbed during installation could be leaking, but water could also be escaping around a tap mounting or from a waste connection. The timing alone is not enough to choose the repair.
With the area safe, we inspect accessible fittings and check for fresh moisture. Controlled checks help separate a pressurised supply leak from water escaping only during use. We may check hot and cold operation separately, stopping if the test adds water to a vulnerable ceiling or enclosed space.
More about leak detection in Westmere
Tracing moisture and agreeing access
The wettest visible spot may sit away from the source because water can follow framing or the underside of a surface. We compare moisture around the new tap connections with the affected area below. Where useful, moisture readings help narrow the investigation, but readings need interpreting alongside direct observations.
Existing cupboards, access panels or exposed pipework may let us inspect the connection. If concealed fittings remain suspect, an opening in a wall, floor or ceiling may be needed. We explain the proposed location, likely disruption and reinstatement arrangements before proceeding. We also explain any required water isolation.
Choosing a repair from the findings
If testing confirms a leaking tap connection, the repair might involve resealing a joint, replacing a damaged connector or correcting how a fitting sits. We check compatibility and condition rather than simply tightening everything. If the leak is elsewhere, we show you the evidence that changes the repair plan.
For newly fitted shower taps, findings may lead to shower repairs at the connection or fitting. We distinguish that work from any separate problem with water escaping around the tap opening. Before repair, we explain what needs replacing or adjusting and whether access affects the surrounding bathroom finish.
Testing the repair and handing over
After the repair, we restore the supply and repeat the checks that revealed the leak. That can include observing the connection with taps closed and checking it during controlled use. We distinguish fresh leakage from moisture already held in nearby materials, which can remain after the source is repaired.
At handover, we explain what was found, what was repaired and any areas we could not inspect. We identify any drying or reinstatement work still needed and tell you what to monitor. Contact us if dripping returns or the patch grows, rather than repeatedly testing the taps yourself.
Leak detection: questions from Westmere
Should I contact the installer of the new taps?
Yes. Tell them when the leak appeared and share photos and installation details. Keep any paperwork available for the inspection. Active leakage still needs prompt attention, so avoid using the affected fittings while arranging help.
Can the taps leak when they are turned off?
Yes. Supply connections upstream of the tap valve remain under pressure when the tap is closed. That is one possibility we check; continued dampness alone cannot confirm where the water originates.
Will you need to open the ceiling below?
Possibly. We first assess accessible connections and the moisture pattern. If the suspected source is concealed, opening a suitable area may be necessary. We explain the access plan before cutting.
More help in Central Auckland
Read before you call
Google reviews
Rated Excellent
Real words from Auckland customers on Google.
Excellent service and reliable people will definitely use them again
4 / 5