Mellons Bay · Gas fitter
Gas Fitter in Mellons Bay
A cooker flame that goes out as you release the knob needs assessment, not a way to keep the control pressed down. The fault could involve the operating sequence, flame sensing or the control itself.
- PGDB licensed
- Site Safe member
- Impac Prequal assessed
- Kiwi-owned since 2012
How it works
Enquiry
Assessment
Quote
Completion
Stop using the affected burner and arrange a gasfitting assessment. Stately covers Mellons Bay. Tell us the cooker model, which burner is affected and whether this happens every time, so the enquiry stays focused on that symptom.
Describe the moment the flame goes out
There is a useful difference between a burner that never lights and one that lights while the knob is held, then immediately extinguishes. Describe what you have already observed. Mention whether the control feels different, whether the flame appeared uneven and whether another burner has shown the same behaviour.
Have the make, model and operating instructions ready. The manufacturer's lighting sequence helps us separate an operating question from a fault needing investigation. You do not need to repeat the problem for a video or remove parts before contacting us. Previous repair records are also useful.
Check flame sensing rather than guessing a part
Many cookers use a flame failure device that relies on heat from the burner to allow gas to continue flowing. A thermocouple is one common component. If the control releases but the flame disappears, that component is a possible investigation point, not an automatic diagnosis or shopping list.
We check the appliance design, the lighting sequence and how the flame reaches the sensing point. The control mechanism and relevant connections also need assessment. A flame sensing fault, poor flame contact and a control fault can produce similar reports from a homeowner. Replacing a guessed part can leave the original problem unresolved.
More about gas fitter in Mellons Bay
Match the repair to the cooker and supply
Before selecting parts or proposing replacement, we check the gas supply at the address and the cooker's identification details. Do not order a natural gas or LPG version just because it looks like the current cooker. The appliance information and actual supply need to match the proposed work.
Following assessment, repair might involve the flame sensing component or the control assembly. The findings and suitable parts determine the work. If replacement is the practical option, discuss the cooker installation as a separate scope. The installer checks the requirements for that appliance, including its connection, ventilation and any relevant flue arrangements.
Keep the control intact while arranging help
Do not wedge, tape or otherwise hold the knob down to keep cooking. Do not bypass the flame failure device or attempt internal adjustments. Gas work must be done by a licensed gasfitter. Check the Plumbers, Gasfitters and Drainlayers Board register when arranging the work, rather than treating appliance familiarity as proof of authorisation.
If you smell gas, avoid flames and do not operate electrical switches. Leave the property and call for help from outside. Treat that as a gas leak response rather than continuing the cooker enquiry. Tell the person you call that you smelled gas, not just that a burner would not stay alight.
Finish with operation checks and clear records
After the agreed work, we check operation, including what happens when the control is released. At handover, ask for the findings, work completed and correct lighting sequence to be explained. Keep the appliance details and repair record together so a future enquiry starts with an accurate history.
Connected gas work needs a Gas Safety Certificate. General and high risk gasfitting need a Certificate of Compliance. For servicing or repairs, the paperwork must reflect the actual work undertaken. Ask which documents apply and keep those supplied with the cooker instructions, rather than expecting identical paperwork for every visit. Keep the certification paperwork with your appliance records.
Gas fitter: questions from Mellons Bay
Does this always mean a failed thermocouple?
No. Flame contact and the control mechanism also need checking. The symptom alone cannot tell us which part needs repair.
Should I hold the knob longer?
Follow the manufacturer's lighting instructions. If the flame still extinguishes, stop using that burner and arrange assessment rather than extending attempts.
Should I buy a replacement cooker first?
Get the fault assessed first. Repair findings, parts availability and the confirmed supply help inform a replacement decision.
More help in East Auckland
Read before you call
Google reviews
Rated Excellent
Real words from Auckland customers on Google.
Actually awesome and the reviews are correct… on time, job well done and sorry about the bad replacement tap I provided you.
5 / 5