Mission Bay · Leak detection
Leak Detection in Mission Bay
A shower waste that leaks only after bathing can leave a damp patch once the shower has stopped, even when everything looked dry beforehand.
- PGDB licensed
- Site Safe member
- Impac Prequal assessed
- Kiwi-owned since 2012
How it works
Call or enquire
Phone us or send the address and what you’re seeing.
We assess
A licensed Stately plumber looks at the job on site.
Clear quote
You get a plain explanation and a clear quote before work starts.
Job done and tidied
We finish the work and leave the site clean.
The waste connection could be involved, but water travelling from another part of the shower can produce similar signs. Stately covers Mission Bay, investigating when moisture appears and how it reaches the visible patch. We start with your observations, then use controlled checks to narrow down the cause before recommending access or repairs.
Notice what happens after use
Before using the shower again, note where the moisture first appears and how long it takes to show. A photograph taken immediately afterwards, followed by another when the patch develops, helps us understand the delay. Record whether the shower drained slowly or water briefly pooled around the waste.
Tell us whether the patch keeps growing after the shower stops, and whether it dries between uses. These details help separate delayed drainage leakage from water stored beneath the tray or around an enclosure. Avoid repeated trial showers, lifting the waste fitting or tightening visible parts yourself.
Check the waste separately
Onsite, we inspect the visible waste, its seating and any accessible connections, alongside the damp area. We also look for routes that could carry water towards the same spot. Moisture appearing below the drain is a useful clue, but its position alone cannot confirm which fitting has leaked.
Where the shower layout allows, we introduce a measured amount of water into the waste while keeping surrounding surfaces dry. We watch accessible connections during discharge and afterwards. Separate, controlled wetting around the waste seating or shower surfaces may then help distinguish a drainage fault from another water entry point.
More about leak detection in Mission Bay
Plan safe access and isolation
An existing access panel or an exposed underside may let us inspect the trap and joints directly. If those areas are enclosed, we explain what remains hidden and whether a targeted opening is needed. We discuss its location and likely reinstatement before proceeding, rather than treating access as automatic.
For a suspected waste leak, keeping the shower out of use is usually more relevant than turning off the entire water supply. We confirm any isolation needed for testing or repair. Keep people clear of a wet or sagging ceiling below, and tell us if moisture is near electrical fittings.
Match the repair to findings
A leak reproduced at the waste seal could call for reseating or replacing that component, subject to its condition and compatibility. A leaking trap or joint would need a different repair. If drainage checks remain dry, we explain that result and investigate the other shower areas implicated by testing.
We outline the confirmed fault, any remaining uncertainty and the access needed before agreeing on shower repairs. Applying sealant over the top is unlikely to address a failed connection underneath. Where surrounding materials are wet or damaged, we explain how that affects the repair sequence and any reinstatement needed.
Retest and explain the outcome
After repair, we repeat the relevant discharge checks and allow time for the delayed symptoms you reported. We inspect the repaired area wherever access permits. Existing moisture may take time to dry, so we distinguish residual dampness from fresh leakage using the observations available during the visit.
Before handover, we explain what was checked, what was repaired and whether anything still needs monitoring or further access. You receive clear guidance on when the shower can be used again. Photograph the original patch afterwards and contact us if it spreads, becomes wetter or returns after bathing.
Leak detection: questions from Mission Bay
Should I keep using the shower?
Avoid using it while fresh moisture is appearing. Use another shower if available, and arrange an assessment rather than testing it through normal bathing.
Why does the leak appear afterwards?
Water can take time to travel along surfaces or collect before becoming visible. The delay helps guide testing but cannot confirm a waste fault by itself.
Will the shower tray need removing?
That depends on the fault and available access. We check accessible areas first and explain any opening needed to confirm or repair the leaking connection.
More help in East Auckland
Read before you call
Google reviews
Rated Excellent
Real words from Auckland customers on Google.
Actually awesome and the reviews are correct… on time, job well done and sorry about the bad replacement tap I provided you.
5 / 5