Devonport · Leak detection
Leak Detection in Devonport
A leak beneath a bath can show up as water along the floor, dampness beside the bath panel or a mark on the ceiling below.
- PGDB licensed
- Site Safe member
- Impac Prequal assessed
- Kiwi-owned since 2012
How it works
Call or enquire
Phone us or send the address and what you’re seeing.
We assess
A licensed Stately plumber looks at the job on site.
Clear quote
You get a plain explanation and a clear quote before work starts.
Job done and tidied
We finish the work and leave the site clean.
The visible patch may be some distance from the actual fault. Stately covers Devonport, and we start by asking when the water appears: while filling, during use, when draining or between baths. That pattern helps us plan checks before deciding whether access beneath the bath is needed.
Notice when the dampness appears
Stop using the bath if water is escaping, and note what happened just before you noticed it. A photo of the wet area and any ceiling mark can help us compare changes. Keep towels clear of electrical fittings, and avoid standing beneath a ceiling that is sagging or bulging.
Tell us whether the bath was full, whether the overflow became wet and whether the patch grew after the plug was pulled. These details guide the investigation but are not proof of a particular fault. Please do not fill or empty the bath again just to reproduce an active leak.
Check each possible water path
Onsite, we inspect the visible bath edges, tap connections and surrounding surfaces before running water. Water beneath a bath could come from a supply connection, the waste assembly, the overflow or water passing an edge seal. We look for moisture tracks and distinguish fresh wetness from older staining where possible.
If conditions allow, we test filling, draining and the overflow separately, using controlled amounts of water while watching accessible areas. We stop if water starts spreading. A leak that occurs only under particular conditions may need further checks; one dry test alone is not enough to rule out a fault.
More about leak detection in Devonport
Agree on access and isolation
An existing access panel may let us inspect beneath the bath, but some connections are concealed behind a fixed surround. We explain what we can reach and where visibility ends. If an opening is needed, we discuss its position, likely extent and reinstatement needs with you before proceeding.
If a supply connection appears to be leaking continuously, we assess whether that feed can be isolated safely. A waste leak may instead require the bath to stay out of use. Do not force stiff valves or remove panels yourself; tell us if another fixture shares the bath controls.
Match the repair to the findings
Once we can inspect the affected connection or seal, we explain what the checks have shown and what remains uncertain. A loose waste fitting, damaged overflow connection and failed bath edge each need different work. Adding sealant around the visible wet patch could leave the actual water path untouched.
We discuss whether the affected part can be repaired or needs replacement, along with access limitations. If an over-bath shower connection is responsible, we explain the shower repairs needed. Wet surrounding materials may need drying or separate assessment, so stopping the escape of water may be only the first step.
Retest and explain what happens next
After the agreed plumbing repair, we repeat the relevant checks and inspect the accessible area for fresh moisture. Where practical, that includes checking the bath as it drains rather than watching only while it fills. Any unfinished testing or remaining concealed area is clearly explained before we finish.
We leave you with a summary of the fault, the work completed and any follow-up needed. You will know whether the bath can be used and whether a seal needs curing time. Photograph lingering marks so you can tell us if they spread rather than gradually dry.
Leak detection: questions from Devonport
Can I keep using the bath?
Keep it out of use while water is escaping or the cause is uncertain. A small visible patch can hide more water beneath the bath. Ask us about safe use after the checks.
Will the bath need to come out?
Not always. An access panel or agreed opening may provide enough room. Bath removal depends on the fault, its position and the space needed to complete and test the repair.
What should I prepare before the visit?
Clear loose items from beside the bath and provide access to the room below, if applicable. Have your photos and timing notes ready. Leave fixed panels and fittings in place.
More help in North Shore
Read before you call
Google reviews
Rated Excellent
Real words from Auckland customers on Google.
Thomas was professional, fast and efficient. He explained things clearly, and honestly. We were about to leave for the South Island for the weekend, Thomas made sure the job was completed in good order before we left. He also checked-in with us periodically to ensure there were no further issues.
2 / 5