Auckland CBD · Gas fitter
Gas Fitter in Auckland CBD
Replacing a gas hob in a stone benchtop starts with the opening, not the showroom label. Before buying, gather the old hob model, the proposed replacement model and photographs of the bench and cupboard below.
- PGDB licensed
- Site Safe member
- Impac Prequal assessed
- Kiwi-owned since 2012
How it works
Enquiry
Assessment
Quote
Completion
Ask a gasfitter to compare the installation requirements with the existing setup. Stately covers Auckland CBD. Discuss the replacement with those details ready, so the stone cutout, gas supply and connection access shape the job from the start.
Match the opening, not just the hob width
Two hobs sold at the same nominal width can need different openings. The visible glass or metal edge hides the cutout underneath. An old invoice or installation drawing can help, but the actual opening needs checking before a replacement is confirmed. Do not lift or disconnect the existing hob yourself to measure it.
We compare the proposed model’s cutout drawing with the opening, corner shape and available supporting edge. We also look at how its underside sits within the cabinet. A hob that covers the hole from above can still conflict with a drawer, oven casing or cabinet rail below.
Keep stone alterations separate from gas connections
The simplest replacement is a compatible hob that fits the existing opening. A larger opening can limit the choice just as much as a smaller one. Decorative overlap alone is not a basis for deciding that an appliance will fit correctly. Its installation instructions guide the assessment.
If stone alterations are needed, agree their scope with a stone specialist before committing to the appliance. Coordinate the sequence: gas disconnection, stone work, then fitting and connection. Do not book stone cutting on the strength of the advertised hob width. Share the manufacturer’s drawing and have the opening checked against it.
More about gas fitter in Auckland CBD
Confirm the supply and the space beneath
Check the gas supply at the address rather than assuming natural gas is available. Provide the replacement model’s gas specification and any information about the existing supply. We check compatibility as part of assessing the installation. The old hob working in that position is not enough information to select its replacement.
Photographs inside the cupboard help explain access, but the connection arrangement needs an onsite check. Tell us about an oven immediately below, fixed drawers or a cupboard back that restricts access. We check the appliance requirements, surrounding space and connection position together rather than treating the benchtop opening as the only constraint.
Arrange removal and fitting around the kitchen
Have the appliance model confirmed before arranging removal of the old hob. Keep its manual and the replacement installation instructions available. Clear the cupboard of stored items and explain who can approve any cabinet or stone changes. If you rent, settle permission for the replacement with the owner before work begins.
Gas work must be done by a licensed gasfitter; you can check the licence on the PGDB register. We disconnect the old appliance and install the compatible replacement within the agreed scope. Any issue found with the existing connection is assessed onsite and discussed before repair. Keep one person available to make decisions about changes to that scope.
Finish with operation checks and the right records
At handover, we explain the controls and the checks completed for the installation. Keep the appliance instructions, model details and gasfitting records together. Connected gas work needs a Gas Safety Certificate. General or high risk gasfitting also needs a Certificate of Compliance. For servicing or repairs, paperwork follows the actual work undertaken.
Ask what was changed, whether any existing components were retained and who receives the records. If you smell gas, avoid flames and electrical switches, leave the area and call for help from outside. Keep the certification paperwork with your appliance records.
Gas fitter: questions from Auckland CBD
Can I order the same width as my old hob?
Not from width alone. Compare the exact model’s cutout drawing, underside dimensions and installation requirements with the existing opening and cabinetry before ordering.
Who should measure a cutout hidden under the hob?
Arrange this with the gasfitter as part of the replacement assessment. Do not disconnect or lift the connected appliance yourself. Existing drawings can help with initial selection.
What if the new hob needs a smaller opening?
Pause the purchase. Ask whether another model fits the existing cutout. Any proposed stone adaptation needs assessment by the stone specialist alongside the appliance installation requirements.
More help in Central Auckland
Read before you call
Google reviews
Rated Excellent
Real words from Auckland customers on Google.
James, came on time. Clean, pleasant. Checked what needed to be done. Worked fast. Good communication
3 / 5